Melting together metal parts?

  • Thread starter Thread starter Oronare
  • Start date Start date
  • The masquerade of murder returns! A new game of Vampires Amongst Us has begun. Unmask the killers, trust no one, and try to survive the night. Find out more and sign up now!
O

Oronare

Guest
Hey guys,

Just wondering if this is a viable option? the metal of the miniatures isn't too strong that it would take immense heat to slightly melt it, and I think two parts (I.E blood knights torso/arm with lance) would be a lot more secure if melted together.

thoughts?
 
I have never really considered doing that before. But to be honest I dont think that is such a good idea.

A friend of mine once got hold of some rubber moulds and some white metal and we tried making our own miniatures one day. What I experienced that day is that molten metal is really hard to control and also it sets in just a couple of seonds. The only way you could possibly do this is by doing it fast as hell with as little metal as you can. But if you are too quick or use just a little bit too much metal it will definitely flow over and long before you are able to even think of removing it, the metal will have gone hard and the whole model is useless.

Just my two cents.
 
I thought about putting my zippo on the table, lit, holt the part in the tip of the flame for a second, test it, just so that it goes slightly, not runny and melted, then i can mash the two parts together and let it set :D

Was just a thought haha.
 
have you considered soldering it? its probably viable if you know what you're doing and have a steady hand
 
You'd need a lot of heat to make an actual bond, and then one mistake and your model is bummed. I've used heat before to adjust the poses of plastics, and that's easy enough to mess up using just a lighter, never mind what you'd need to melt metal. Not to mention that for a true bond you'd really want to melt both surfaces slightly and join them while both were molten. Sounds like an easy way to burn a hole through your fingers, if you ask me.

Soldering sounds like a pretty bad idea too, I've got to say... you'd likely end up with some mess all around the joing that, for the effort of removing it, isn't worth it. If you're prepared to go to the hassle of melting stuff, you'd be as well as just pinning the parts and using some araldite instead of glue.
 
Pinning &/ Epoxy Resin (as CB says, Araldite for example but it's not the only brand out there). Personally I've hardly ever used epoxy glue because a well executed pin or two with strong wire & superglue will hold virtually any model together. Regarding melting model parts together, there's no way you can feasibly do it without ruining the detail, I pissed about with models, lighters & nail polish remover many times in my youth, it takes a lot of heat (certainly more than could be usefully controlled) to liquify the metal & the detail goes long before the flat contact areas would.

Pinning is a necessary skill for serious modelmakers.
 
As metal conducts heat you wouldn't be able to hold any part of the model with your hands, so you would have to use gloves at the very least (quite thick ones) aand as the metal sets quickly you'd struggle to get it in the right place and it its wrong then you'll struggle to get it apart. The conducding of heat may also damage the detailing on other parts of the model.

As mentioned above apoxy resin sets very hard if you wanted something really strong, but imo pining and superglue should work fine.

Soldering would make a mess and isn't accally that strong and it only sticks well to certain metals
 
Im a welder and I tried melting some scrap pewter just to see how it reacts, it became extremely fluid very quickly and then set very quickly as well. ive never actually tried welding them together because as soon as I brought two pieces together they were attracted to each other and instantly came together, similarly to when t-1000 was frozen and then when the pieces thawed they came together. pretty much when I heated it, even with the smallest amount of heat with the welding torch, it instantly became fluid like entirely and the part became a big blob. Iv'e always thought maybe soldering it would be a better idea but I never got around to trying that.
 
Well we seem to have a wealth of knowledge on metallurgy on CN! Anyway the consensus seems to be not to bother, which is helpful as it was something I considered, especially when it came to larger models. I'll sticking to pinning and superglue then.
 
Welding pewter or zamak is exteremely unfeasable.
Tin melts at 291C(505F) and zinc melts at 420C(790F), even the outer envelopes of an oxyacetylene blowtorch is 1260C(2300F), you will need a steady and precise flame for tis process so use your zippos for lighting cigarettes only. Also these metals are chemically very active, they will oxidize almost immediately on high tempratures. Leaving you with ugly slag in the middle of the miniature which can only be removed with grinding. These metals are not thermally stable also, their strenght will drop dramatically in the middle of the process and your mini will be deformed after it.
Soldering may be feasable using pure tin-zinc agents but soldering is a hard and messy process and will leave your mini with drops of solder alloy here and there.
Adhesive bonding is optimal for these metals. Epoxy and glues will work wonders. Use drilling and inserting brass rods if you are having so much trouble.

And if you are determined to weld or solder your mini don't do it inside your home. Almost every metal release toxic gases when welding or soldering.
 
I am interested to this thread .,But I am a little confused about this Welding pewter or zamak.,Can you add more information about this thing.,


_________________
 
You can solder them, as mention, but it's much messier than pinning, and only useful in areas you can file to clean up (IE not too much detail, like a sword blade that broke, for example).
 
It just so happens that I have a model I need to fix that is more or less unpinnable, due to the small size and the irregular angle of the parts(basically, an Eldar Harlequin snapped near the base where the cloth thingy nears the slot). Also, as a former engineering student I do happen to have a solder gun, solder sucker and...plenty of solder wire. Would that be suitable to the occasion? Filing off any unwanted overspill is not a problem
 
I experienced that in order to have fluid metal the temperature would have to remain high enough for it to melt during the entire process. That means that any fluid metal will be hot enough to melt metal from other sources as well, which in turn would potentially eat away at the miniature when the fluid metal was applied. I would try it out on another model before doing anything about that harlequin of yours. If not done properly the model would suffer from a devastating effect, and you'd end up with less miniature than when you started.

As I said earlier in this thread I tried casting miniatures once, but you shouldn't take what I say as canon though.
 
It would still be easier to clip off a further couple of millimetres of robe then file down the surface to allow more room to drill a pinhole, then fill in any unsightly areas with green stuff. I'd suggest gluing an offcut metal tab (I'm sure there are plenty of these tabs on the harlequin models) onto the underside of a base and drilling down into it to anchor the pin (it would also add some stabilising weight).
 
You could also litter the base with objects to hide the repair and glued strategically to support the model better.
 
i know flame welding wouldnt work due to melting the whole model, but what about arc welding? would that work, as the models would be fused in position rather than melting then mashing together.
 
Short answer is no.
Long and boring answer is, first zamak or pewter is the material used to cast these models. Both of them have low melting points (381—387 °C,718—729 °F). The model won't stand up to your arc temperature which ranges from 6,000 °C (10,000 °F) to relatively low levels due to the ampere used when welding. Second, electrical conductivity is very important in arc welding and as far as i know zamak or pewter are not good for arc welding. Third if you have ever seen a gmaw(Gas metal arc welding) or gtaw(Gas tungsten arc welding) nozzle, they are as big as your miniature. Impossible to weld precise points. And everything I have written above still applies.

And my advice to welding enthusiasts, welding a miniature is like killing a cockroach with a .50 caliber machine gun, it is overkill. Simple adhesives are enough for metals of this size.
Welding is an industrial operation. Generally used for joining steel, which can not be done any other way possible. Welding is an application of narrow utilization, anything other than steel(even iron) and trigger happy welder will not want to weld it. People worked really hard to just weld aluminum. And it is still a hard process to handle.

I wish I had a welding machine to waste a few good minis to bust this myth. Unfortunately I have neither the resources nor the time.

My wildest guess will be that: A really talented welder with a Gtaw welding machine may be able to weld a miniature. But only thick parts tail of a torso of a Nightbringer for example. But even that will ruin the mini for good.
My realistic guess is your mini will explode in a fiery and awesome manner when such attempt even tried. Because welding is a chemical process as well as physical and active metals and lots of heat is never a good idea.

My advice to hardcore welding enthusiasts is use correct protection and do it somewhere nicely ventilated(Never in home!).

Forgive my endless abuse of English language .
 
Melting those two parts to weld them together will only damage the structure of the miniature.

Drill a hole in each part, pin it together, it'll be really strong.

I've done so for my executioner's (dark elves) swords, the blade has to be glued to the handle held in the small hands of the models, I pinned those with a power drill and a #68 bit (1/32" or .787mm).

Pinning is the solution to most any miniatures that need a solid bond between 2 parts.
 

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

Quick Navigation

User Menu