Fun With Dettol- A Guide to Paint Stripping

  • The masquerade of murder returns! A new game of Vampires Amongst Us has begun. Unmask the killers, trust no one, and try to survive the night. Find out more and sign up now!

Sanai

Stylish Deviant
True Blood
Oct 30, 2009
5,193
Behind Darvy
Zombies
4,233
So I have over the years experimented with various different ways of stripping paint.

I have used Simple Green, Dishwashing Liquid and Windex... but none of them did me much good.

Until I happened along to articles about paint stripping with dettol- so I decided to give it a try, and here is what I found.

WHAT YOU NEED
  1. Some painted models to strip. Metal, Plastic or Resin, it doesn't matter.
  2. Some Dettol. Not the clear stuff, the brown stuff.
    dettol-antiseptic-liquid.webp
  3. A toothbrush. I bought a cheap electric toothbrush to save me some effort, but any cheap or old toothbrush will do.
  4. Other tools for scraping paint of things- toothpicks, old used up brushes, dental tools if you have them, etc etc.
  5. Dishwashing Liquid
  6. Some buckets and/or containers to put things in.

WARNINGS
Before we start, here are some important warnings.
​
  1. This warning is the most important. At some points you may be tempted to rinse the models or toothbrush is water. At no point during the process should you do this! If you introduce water to a model that has been soaked in dettol, it will form a gluey, tarry residue which is difficult to remove from the model, and over which paint won't really stick properly. I will cover how to properly rinse things later in this guide.
  2. Be aware that the dettol solution, and your models, will have a very strong smell. I would advise wearing some decent gloves while doing all of this. However, as far as I can tell it is no where near as harmful as other paint strippers (like break fluid) can be. Use a well ventilated area.

ONTO THE FUN STUFF

  1. First, you need to prepare the dettol solution. In your planned soaking container, mix a 1:1 solution of the Dettol & water. It will look kinda foamey and white. (And it will stink to high heaven)
  2. Next, get any models you wish to strip, and immerse them in the solution.
  3. Leave them in the solution for a few hours (though it is best to leave them for 24 hours/overnight). Do this with a sealable container, or leave it somewhere were the fumes won't get to you.
  4. Once the models have been soaked, its time to get all of that paint off. It should come of fairly easily- just scrub the models with a toothbrush, and use a toothpick or dental tools or whatever to get the gunky paint out from any crevices.
  5. If you need to rinse the models, or the toothbrush, rinse them in the dettol solution- remember, we can't introduce water to these models!
  6. Once you have gotten rid of all of the paint that you can, its time to rinse the models!
  7. In another container or bucket (or even a sink) mix some dishwashing liquid with warm (but not hot) water.
  8. Rinse the models in this dishwashing liquid/warm water solution.
  9. Check the models for any remaining gunk and residue- if theres still gunk or residue of any kind, you need to scrub them some more and rinse them again until its all gone, or even return them to the dettol for more soaking.

THE RESULTS

If you follow the steps correctly, you will generally find that plastic models will be stripped bare- even paint in the crevices can be reliably removed!

I have not yet tried it on metal, but I have been told that metal models come out even shinier than they originally were.
​
 
The thing I find interesting here is that you dilute the Dettol with water before you start. I always use it neat from the bottle, because of the problems I've had with getting water anywhere near the paint residue. And yes, he really means DO NOT get water involved, I spent an hour cleaning a sink after the first time I tried using Dettol!

The smell is a problem, especially as I suspect the pine oil is not an active paint stripping ingredient. (I worked out an approximate chemical make up of Dettol and looked into making a home brew version without the smell, but it seems more expensive and more hassle.) I keep my Dettol in a lidded plastic bucket in the garage. To prolong its useful like I strain it through a cheap plastic sieve now and then to remove paint lumps. I keep a jam jar of new Dettol to hand for the final rinse of each miniature, before getting water involved.

The smell on the miniatures does linger. If you can leave them outdoors for a while all the better, but I find normal spray undercoating "seals in" the smell. Do wear gloves (and old clothes ideally, as I always get spattered in Dettol and gobbets of paint!)

It works fine on metal minis (though I typically use harsher chemicals on those) and I have left both metal and plastic GW minis in it for months at a time without harm to the base material.

@hairyjeff - I'm in the UK and it works fine for me.
 
I am going to try fairy power spray next (as the small bottle of dettol I bought to try has run out). That is, if I can find it in Australian stores.

I mostly dilute the dettol because I have a very limited budget, and the bottle I was able to buy was a small one- for the 10 or so models I stripped, I would have had to use the whole bottle if I didn't dilute it. If I could find a place that sells the big bottles I would probably just use it without water.

I will post back in this thread once I have tried out the fairy power spray (I think Fairy Power Spray is the last of the various different commonly used chemicals to try, having tried dettol, simple green, detergent & windex). Well, that is except break fluid, but I am not going near that stuff.
 
Dettol sounds good, but it just seems like effort still. The risk of models becoming a sticky mess of melted plastic is enough to put me off. I still maintain that neat methylated spirit is by far the best stripper I have come across. Not only is she very arousing with her lovely purple hue and combustability, she also leaves the models as clean as the day you bought them. Fairly safe to use, good on all model types and cheap to boot. I don't know why nobody likes her.

u_m
 
I have found the dettol doesn't really melt the plastic at all- Just the paint.

I will give metho a try at some point (I want to try all of the options to see which works best)
 
This is neat! I accidentaly spilled alot of paint on my vampire lord convertion and need to wash him clean. Gonna try your guide but first need to find some dettol here in Scandenavia. Should be able to order it online otherwise.
 
U_M..... I like meths! I have used it several times.
( side note to naughty people- if you mix parfait d'amour and vodka 50/50, it looks like you're drinking meths, and totally freaks your Granny!)
 
Dettol works excellent on plastic and metal, but don't let your finecast sit in it for too long. I've tested some leftover FC sprue and it became soft and bendy.
Do wear gloves! Dettol really dries out skin. Once or twice I've had a sharp metal part of a mini tear open my glove and some of the dettol soaked my hand while I kept working: the next day it was dry enough for some of my skin to just flake off. It doesn't hurt or anything, just like when your skin can get really dry in winter, but it's something to keep in mind.
 
Found an odd import store that sold dettol!
First time on the balcony, on my new outdoor furnitures. Despite all that could go wrong according to murphys laws, it went well. Used a plastic tub with two glass jars of dettol. Model came out a tad gritty but it's nothing i can't hide with paint. Also have to re-do some greenstuff since the dettol ate that too. Wonderous liquid! It shall be used again in the future.
 

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

Quick Navigation

User Menu