RE: Need technical advice concerning NMM and OSL - pics of finished testmini online - C&C welcome
To get this thread back on topic I've decided to upload a commented compiliation of the most characterful pieces I've done in NMM and the progress I've made in regard to improving the technique. I'll try to explain what was helpful, what worked and what didn't.
Here you go:
The first picture shows my last GB entry and the second one my first attempt at NMM after putting most of the advice in this thread into practice.
You can clearly see my technique improved a lot compared to the first attempt. The reasons for this are as follows: The most evident changes were made to the gold formula. In my first attempt I started with scorched brown (no calthan brown available), worked upwards to snakebite leather and then added progressive amounts of bleached bone to the transition. As you can see on the hood this can work, but is not perfectly realistic as for example the sword's hilt does not look all that metallic. To get by this problem I tried to make the gold effect shinier. I altered the recipe as follows:
Basecoat with Scorched brown
Wet blend up to Snakebite leather in as many steps as you think is appropriate. Generally the bigger the surface the more steps I'd take.
Wet blend from Snakebite Leather to Bleached Bone (same rules as above apply)
Up to that point it's all the same except that my blending improved a lot with practice, but here is the really important part:
apply hard contrasts with thin but sharp lines of pure scorched brown and only blend to one side, you want one edge to keep the hard contrast, just as u_m said, NMM rewards bravery. Keep a metallic object near you for light reflex references.
apply a thorough glaze of Sunburst Yellow, be careful not to erase the colour transitions you created before though, just make sure the colour gives the surface a slight yellow touch.
apply a fine glaze of purple, yes, purple - a dark one preferably. It just adds a certain something to the mini.
Pick out the extreme highlights with a mix of Bleached Bone and Skull White or pure Skull White. If you feel it necessary you can of course reapply your darkes shade again as well, but don't overdo it or you will ruin the effect created through the glazes.
This is how I do gold at the moment, but I'm still experimenting and open for new thoughts.
The steel is a lot easier to do as you are just working with wet blends of black and white basically, however I've found that leaving areas completely black is not that good for larger surfaces, i.e. the axe blade. Imo you should keep the pure black and pure white areas as thin as possible as they resemble the extreme shades or reflexes in the metal, thus you should at least give most of the blade a coat of dark grey and work from there, you can then re-blacken the areas you want to have as extreme shades. This is what I am kind of unhappy about with the blade, starting with black and working up to white however works incredibly good on smaller surfaces (see the chains and the rest of the axe).
Lastly with a monochromatic (black & white) base you can add whichever colour you want to create magical steel or just give the metal that tiny hue of colour to make it look more lively with a simple glaze of said colour. Best example for this is the sword of my little Wood Elf soldier.
To come back to the "how to do larger steel surfaces sufficiently" again I'd like to give the example of my Green Knight
This is him with the first version of the blade, it has been redone since to look more like the one on my wood elf, except for a green glaze. What I'm getting at though is that you can clearly see the black areas that are there, yet not too big, especially most of the helmet is grey which comes closer to the normal "colour" of steel. If I had left more of it black it wouldn't have a metallic feel to it. Best advice here as I can't give you a perfect formula is have something near you for reference. Try to find a way between thorough colouring, working smooth and adding harsh contrasts.
Best results, as always, come with practice.
I have yet to try something that is called SENMM (sky-earth-non-metallic-metal), which is basically a highly reflective surface like chrome. It is incredibly hard to do and either looks completely awesome or silly. Should I ever try it I'll post up the results and a tutorial if there is a demand for it.
I hope this article will help all of you out there who struggle with NMM, I tried to sum up the most important things I currently know about it. Feedback is of course appreciated and encouraged. If need be I can repost this as a separate tutorial, I currently can't provide any step by step instructions which is why I left it at this.
All the best,
Dogmar